Would you like to react to this message? Create an account in a few clicks or log in to continue.

autocad 2006 & 2007

+3
Bosepvance
kurdaps!
herald_101683
7 posters

 :: General :: Help Line

Go down

autocad 2006 & 2007 Empty autocad 2006 & 2007

Post by herald_101683 Thu Jan 06, 2011 1:18 am

Mga Master sa autocad patulong naman kung pano ko maayos yung sa command line ng autocad kasi tuwing ginagamit ko yung line eh hindi sya straight line, bumabaluktot ng gma ilang degrees. pano po ba maayos to? salamat po.
herald_101683
herald_101683
CGP Apprentice
CGP Apprentice

Number of posts : 338
Age : 41
Location : singapore
Registration date : 21/03/2010

Back to top Go down

autocad 2006 & 2007 Empty Re: autocad 2006 & 2007

Post by kurdaps! Thu Jan 06, 2011 1:22 am

F8?
kurdaps!
kurdaps!
Super Moderator
Super Moderator

Number of posts : 5060
Age : 46
Location : aan-dxb-aan
Registration date : 18/09/2008

http://www.sherwinboston.com

Back to top Go down

autocad 2006 & 2007 Empty Re: autocad 2006 & 2007

Post by herald_101683 Thu Jan 06, 2011 1:25 am

sir kurdaps pang horizontal & vertical straight po yan db? kasi yung sakin naka 5 degrees yung line kpag gumagawa ng straight line. salamat ulit.
herald_101683
herald_101683
CGP Apprentice
CGP Apprentice

Number of posts : 338
Age : 41
Location : singapore
Registration date : 21/03/2010

Back to top Go down

autocad 2006 & 2007 Empty Re: autocad 2006 & 2007

Post by Bosepvance Thu Jan 06, 2011 1:34 am

try the following "ucs enter" + w enter. then try to draw a line again. hope it works sir
Bosepvance
Bosepvance
CGP Apprentice
CGP Apprentice

Number of posts : 462
Age : 43
Location : Makati
Registration date : 20/10/2008

Back to top Go down

autocad 2006 & 2007 Empty Re: autocad 2006 & 2007

Post by krizaliehs07 Thu Jan 06, 2011 1:36 am

mam try mo type UCS tapos lagay mo sa world,then saka ka mag f8, try lang kung makatulong Very Happy
may nauna na pala Very Happy
krizaliehs07
krizaliehs07
CGP Apprentice
CGP Apprentice

Number of posts : 763
Age : 45
Location : Kesong Puti & Buko Pie
Registration date : 20/07/2009

Back to top Go down

autocad 2006 & 2007 Empty Re: autocad 2006 & 2007

Post by herald_101683 Thu Jan 06, 2011 1:46 am

krizaliehs07 wrote:mam try mo type UCS tapos lagay mo sa world,then saka ka mag f8, try lang kung makatulong Very Happy
may nauna na pala Very Happy

sir po ako. salamat po. try ko po.
herald_101683
herald_101683
CGP Apprentice
CGP Apprentice

Number of posts : 338
Age : 41
Location : singapore
Registration date : 21/03/2010

Back to top Go down

autocad 2006 & 2007 Empty Re: autocad 2006 & 2007

Post by ERICK Thu Jan 06, 2011 1:57 am

if all else fails try this..

type snapang enter, then type 0 (zero) then enter

baka kase nakaset ung angle snap nyan, pero make sure naka world din ung ucs mo...
ERICK
ERICK
CGP Dark Horse
CGP Dark Horse

Number of posts : 3907
Age : 43
Location : Makati, Philippines
Registration date : 18/09/2008

http://www.ericktorio.tk http://www.coroflot.com/ericktorio

Back to top Go down

autocad 2006 & 2007 Empty Re: autocad 2006 & 2007

Post by Bosepvance Thu Jan 06, 2011 2:14 am

i agree with sir Erick, kung hindi pa umubra yung mga nauna sigurado yung suggestion ni sir Erick! good luck!
Bosepvance
Bosepvance
CGP Apprentice
CGP Apprentice

Number of posts : 462
Age : 43
Location : Makati
Registration date : 20/10/2008

Back to top Go down

autocad 2006 & 2007 Empty Re: autocad 2006 & 2007

Post by jarul Thu Jan 06, 2011 5:08 am

ERICK wrote:if all else fails try this..

type snapang enter, then type 0 (zero) then enter

baka kase nakaset ung angle snap nyan, pero make sure naka world din ung ucs mo...

agree
jarul
jarul
CGP Hero
CGP Hero

Number of posts : 5814
Age : 38
Location : lugar nga dghan ug DDS.....
Registration date : 04/11/2008

http://jarulvisuals.weebly.com/

Back to top Go down

autocad 2006 & 2007 Empty Re: autocad 2006 & 2007

Post by Nayve Thu Jan 06, 2011 6:54 pm

o baka naka isometric snap sir?

try to right click mo sa icon ng "snap either grid display will do,( doon sa baba ng command ) click setting,

choose "snap and grid", under "snap type" click rectangular snap

saan makatulong
Nayve
Nayve
CGP Apprentice
CGP Apprentice

Number of posts : 730
Age : 41
Location : Laguna
Registration date : 06/09/2010

Back to top Go down

autocad 2006 & 2007 Empty Re: autocad 2006 & 2007

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 :: General :: Help Line

 
Permissions in this forum:
You cannot reply to topics in this forum