drawing file is not valid

Dudes, hingi lang ng tulong. nag o-open ako ng cad file then nage-error. "drawing file is not valid" old drawing na sya and save within this computer im using. pag nag thumbnail naman ako napre-preview ko yung drawing.....no kaya ang problem ng file....tina-try ko rin mag auto-recovery pero "unable to recover file". bad trip ito......ayaw kong ulitin buong drawing....im using autocad 2010lt. and ang mga file is save to 2004 version.

Sir mron pa po bng .bak file yang drawing nyo? kng mron sir try nyo pong palitan ung extension name nya ng .dwg.
sample : drawing1.bak = drawing1.dwg

baka dahil LT ang gamit mo bro?

dumzblood wrote:Sir mron pa po bng .bak file yang drawing nyo? kng mron sir try nyo pong palitan ung extension name nya ng .dwg.
sample : drawing1.bak = drawing1.dwg

wala ng .bak file bosing....hinahanap ko nga e....month old na yung file kasi....

bokkins wrote:baka dahil LT ang gamit mo bro?

isa na rin siguro yun sir boks, pero dapat coordinated ang filing ng autocad e...hmmm...

meron kayang software para dito....importante pa naman itong file na ito sa opisina namin.......

malaki ba yan, send mo sakin sa bokkins@yahoo.com. pag di ko mabuksan, meaning sira na ang file. 2004 gamit ko.

bro on your version 2010 type on the command line OP then enter tapos sa file OPEN AND SAVE tab go to FILE SAVE and change it to autocad 2000/200LT drawing para maopen mo ung mga old files.

ah..so yung file is ACAD 2004 version...ganito..actually same as sir kietsmark solution...since ACAD 2004...eto gawin mo...

1. open those file in ACAD 2004
2. Sa ACAD 2004, type OP, sa file save as, set mo to autocad 2000/2000lt
3. save as mo yung mga drawings
4. then try to open it now in ACAD 2010lt.

I guess it will work now...

Hope this helps...

kietsmark wrote:bro on your version 2010 type on the command line OP then enter tapos sa file OPEN AND SAVE tab go to FILE SAVE and change it to autocad 2000/200LT drawing para maopen mo ung mga old files.

ala dude ayaw pa rin gumana.....

arkiedmund wrote:ah..so yung file is ACAD 2004 version...ganito..actually same as sir kietsmark solution...since ACAD 2004...eto gawin mo...

1. open those file in ACAD 2004
2. Sa ACAD 2004, type OP, sa file save as, set mo to autocad 2000/2000lt
3. save as mo yung mga drawings
4. then try to open it now in ACAD 2010lt.

I guess it will work now...

Hope this helps...

sir thanks sa tulong pero yung file save sya sa autocad 2010lt version...tpos yung sa OP naka set na sya as 2004/LT2004 dati pa nung na-save yung file. kaso ayaw pa rin gumana....may balat ata ako sa puwit.....

if all else fails... theres something wrong with the file... might as well do it again...

ERICK wrote:if all else fails... theres something wrong with the file... might as well do it again...

WHOAAA...sir erick, ngayon ka lang nagparamdam......worst come to worst, malamang ganun nga mangyayari.....BT

@f-fortyone: pa PM ng file....tingnan ko dito kung mabubukas...

weird ung file normally it will open kasi naset mo na ung autocad 2010LT mo to open file made with older versions... maybe the file was made on release 14 autocad hehehe

f-fortyone wrote:

ERICK wrote:if all else fails... theres something wrong with the file... might as well do it again...

WHOAAA...sir erick, ngayon ka lang nagparamdam......worst come to worst, malamang ganun nga mangyayari.....BT

heheh naging busy lang norms.... ano ba history nung file kase na yan? baka kase... me ibang mga shapes and unknown objects kase yang cad bago nag save kaya ganyan...lalo nat 2004 pa nag save...or baka... galing higher version, tapos sinave sa lower version... nag edit then save 2004.. pwedeng ganun yan... parang nalito ang cad... or pwedeng ibigay mo sakin yang file.. tignan ko kung maopen ko...

corrupt na yata ang file na yan... try mo install ulit ang CAD mo if wala na talagang ibang option..

ala tlaga mga cgpips...malamang corrupted yung file sinubukan ko na lahat at....sir arkiedmund....daming salamat din sir arkiedmund sa tulong...maraming salamat mga cgpips!!!! ulitin ko na ito malamang.........

hahaha, dre, naemail ko na sa yo yun pdf version nyan file natin... good thing converted from cad to pdf... hehe convert mo na lang ulit from pdf to cad... ok na siguro yun

pwdba ma convert from pdf to cad? hind ko pa alam yan ahh.. paano po sir?

@ mokong, meron nyan bossing may free softwawre na pwede e-download sa net limited lang...pdf to cad...very useful...yun nga lang once na convert sabog ang mga lines, dimensions hatch, etc....pati yung text ng pdf gagawin nyan group of lines..medyo pangit din gamitin

@marcelinoiii, wag na ulitin ko nalang yung drawing nakita ko na yung lumang reference from archi...hehe...tignan ko nalang ko mare-generate ko yung sheet may hard copy naman e.....hehe....

try mo to drag and drop it while autocad program is open...otherwise talagang corrupted na ang file

hehe, meron sir nadownload si f-41, ask ntin sya... la din ako nun e.. hehe

calling calling f-41... enlighten us please!

render master wrote:try mo to drag and drop it whil the cad program is open...otherwise talagang corrupted na ang file

na-drag ko na rin sir, ganun din ang error...salamat bossing, ok na ito nasimulan ko na rin gawin and nasa 70% progress na rin ako sa pag gawa...hehe..swerte ko lang nakita ko yung reference na file......

send mo sakin ang file baka matulungan kita... may solution pako jan bro...butch.hbamanila@gmail.com

bro...sad to say corrupted na yang file mo...na try mo na ba isend sa mga nag rerequest na iopen nila sa kanila?...

thanks mga bosing sa pagdamay...hehe malapit ko na rin matpos yung bagong file re-generate ko nalang ulit yung drawing...hehe...no need na!!!salamat po ulit......