ISOMETRIC LAYOUT cad

hello help naman po sa tamang pag gawa ng isometric layout para sa plumbing layout...sawa na kse ako sa style na ginagawa ko....dahil di ko alam ang way sa 3d...2d setup lang ako....Kung may alam po kayo way post nyo nalang po ang tutorial dito hehhee...

ito po ang setup ko...2d isometric layout
1. vpoint -1,-1,1
2. ucs > view
3. blocks the plan
4. oops (di ko alam para san ito hehehe)
5. vpoint 0,0,1
6. ucs > world
7. snapstyle > from 0 change to 1
then press F5

so sana may iba pa kayo setup para maiba naman yung galing sa book ng microcad laking tulong ito sa amin TIA

Boss Vhin try "rotate3d" sa command line...

cloud20 wrote:Boss Vhin try "rotate3d" sa command line...

pwede po paki elaborate? hehehe......d ako familiar sa rotate3d command

Owkie...

1. Rotate subject at 45 degrees...
2. Type ROTATE3D on the command line...
3. Select/window everything that you want to include in your isometry...
4. I usually "right-click" on the mouse after this which is the same as any "enter" command AFAIK...
5. Click anywhere on the screen go left click...
6. Type -60 on the command line...

Credit goes to Master Sundance for teaching an old dog some new tricks...

In my case i usually do it this way:

1. Hold the alt key and key in the following in succession v+3+s.
2. type UCS, press enter or the spacebar and key in v.

Now you can start working on your plumbing isometric.

Hope this helps.

salamat po mga master...ill try this

ako naman iba. sa paperspace ako gumagawa ng isometric plumbing plan

1. set the plan na gagawan ng isometric drawing. normally im working with layeres kaya kung alin man ang di ko gusto makita sa or makasama sa isometric layout, ino-off ko lang

2. go to paperspace, create viewport

3. double click viewport to activate then make it an isometric view, depende sa yo kung aling isometric ang gusto mo, merong mga choices doon sa View toolbar, pueding SE isometric, SW, NE, NW. kung ok na, hit again the paperspace button para di na sya maging active

4. create new layer say vport then hit the printer icon for it para di maging printable ang layer na iyon

5. kapag ok na ang view, and the viewport scale, inilolock ko na ang viewport view. punta lang sa properties ng viewport ( select the viewport and hit control 1, makikita mo doon ang properties ng viewport including display locked - gawin mong yes)

6. then shift to snapstyl = 1

7. proceed to making your isometric layout.

8. im using this to minimized objects counts.

note: kapag medyo malabo s inyo request nyo lang and i will do a picturial tutorial.

render master wrote:ako naman iba. sa paperspace ako gumagawa ng isometric plumbing plan

1. set the plan na gagawan ng isometric drawing. normally im working with layeres kaya kung alin man ang di ko gusto makita sa or makasama sa isometric layout, ino-off ko lang

2. go to paperspace, create viewport

3. double click viewport to activate then make it an isometric view, depende sa yo kung aling isometric ang gusto mo, merong mga choices doon sa View toolbar, pueding SE isometric, SW, NE, NW. kung ok na, hit again the paperspace button para di na sya maging active

4. create new layer say vport then hit the printer icon for it para di maging printable ang layer na iyon

5. kapag ok na ang view, and the viewport scale, inilolock ko na ang viewport view. punta lang sa properties ng viewport ( select the viewport and hit control 1, makikita mo doon ang properties ng viewport including display locked - gawin mong yes)

6. then shift to snapstyl = 1

7. proceed to making your isometric layout.

8. im using this to minimized objects counts.

note: kapag medyo malabo s inyo request nyo lang and i will do a picturial tutorial.

si medyo na gegets ko na rin kase snapstyle din gamit ko..pero thru 2d mode lang...
alam ko marame ang hirap dito...kaya sana may tym ka po na ipakita sa amin ang image ng mga nasabing hakbang sa paggawa ng isometiko hehehe....salamat master

ditto on cloud.... we have the same workflow.. hehehe

ERICK wrote:ditto on cloud.... we have the same workflow.. hehehe

Fast & simple neh master Erick...

cloud20 wrote:

ERICK wrote:ditto on cloud.... we have the same workflow.. hehehe

Fast & simple neh master Erick...

absolutely sir master super saiyan cloud.... hehehe

samin before we try it on this one..

1. go to "View Toolbars" > "SE Isometric"
2. then type UCS then "View" or v
3. then just highlight and copy the floorplan
4. then go back to Top View then just Paste

that way flat lahat ng drawing mo with the floorplans and elevations.. hope it helps...

I agree with abl_langs talagang yun din ang ginagawa ko!

abl_langs wrote:samin before we try it on this one..

1. go to "View Toolbars" > "SE Isometric"
2. then type UCS then "View" or v
3. then just highlight and copy the floorplan
4. then go back to Top View then just Paste

that way flat lahat ng drawing mo with the floorplans and elevations.. hope it helps...

Mas ok etong procedures ni abl_langs.
ako kase gusto ko malinis ang main floor plan. anuman ang maging revision sa model space, update kaagad ang main floor plan sa isometric.

oo nga master...ok ung tips ni sir abl_langs! tnx ......

abl_langs wrote:samin before we try it on this one..

1. go to "View Toolbars" > "SE Isometric"
2. then type UCS then "View" or v
3. then just highlight and copy the floorplan
4. then go back to Top View then just Paste

that way flat lahat ng drawing mo with the floorplans and elevations.. hope it helps...

oo ito din ang ginagamit ko. meron lang akong gusto idagdag..

5. use polar tracking of increment angle of 30deg para medyo mapabilis ang trabaho nyo.
6. at sa paggawa naman ng circles na isometric.. set nyo muna ang grid and snap setting>snap type group>tick isometric snap. den use ellipse>isocircle>> just continously press F5 to choose orientation.

sana makatulong!

arkiedmund wrote:In my case i usually do it this way:

1. Hold the alt key and key in the following in succession v+3+s.
2. type UCS, press enter or the spacebar and key in v.

Now you can start working on your plumbing isometric.

Hope this helps.

oo nga bro tama c arkiedmund ito ung ginagamit ko pag plubming lay-out...subukan mo nlng to bro parang ito ung easy way for plumbing lay-out.

abl_langs wrote:samin before we try it on this one..

1. go to "View Toolbars" > "SE Isometric"
2. then type UCS then "View" or v
3. then just highlight and copy the floorplan
4. then go back to Top View then just Paste

that way flat lahat ng drawing mo with the floorplans and elevations.. hope it helps...

2nd the motion..ok to..pre..

abl_langs wrote:samin before we try it on this one..

1. go to "View Toolbars" > "SE Isometric"
2. then type UCS then "View" or v
3. then just highlight and copy the floorplan
4. then go back to Top View then just Paste

that way flat lahat ng drawing mo with the floorplans and elevations.. hope it helps...

yup ok to..simple lang...para mas madali pa sir at hindi nyu na kelangn magpunta sa view tab right click sa tool bars then click views..lalabas ng yung tool bar para sa SE isometric and the other views such as SW view, NE, NW,top,side left, or press F3 para diretso s top,left and front view,....sna nakatulong din to...
thanks to sir kietsmark and sir f-fortyone for this tricks...

ayos to sir ah... salamat.. may natutunan na naman ako....

ishae_clanx wrote:

abl_langs wrote:samin before we try it on this one..

1. go to "View Toolbars" > "SE Isometric"
2. then type UCS then "View" or v
3. then just highlight and copy the floorplan
4. then go back to Top View then just Paste

that way flat lahat ng drawing mo with the floorplans and elevations.. hope it helps...

yup ok to..simple lang...para mas madali pa sir at hindi nyu na kelangn magpunta sa view tab right click sa tool bars then click views..lalabas ng yung tool bar para sa SE isometric and the other views such as SW view, NE, NW,top,side left, or press F3 para diretso s top,left and front view,....sna nakatulong din to...
thanks to sir kietsmark and sir f-fortyone for this tricks...

eto rin before ang ginagawa ko, much easier!

abl_langs wrote:samin before we try it on this one..

1. go to "View Toolbars" > "SE Isometric"
2. then type UCS then "View" or v
3. then just highlight and copy the floorplan
4. then go back to Top View then just Paste

that way flat lahat ng drawing mo with the floorplans and elevations.. hope it helps...

+1

ako naman po ginagamit ko flatshot.

1. extrude the floor plan na gusto mong gawan ng plum layout.
2. type flatshot then enter.
"may magaapear na setting. mamili ka lang kung san mo isasave"
3. open mo yung sinave mo.
"pag na open mo na siya, naka top view siya pero isometric ang labas niya. Idelete mo lang yung mga horizontal lines. ang matitira yung plan mo."

"i block mo na rin boss, para mas maganda.

ayos to isa n nmang tutorial.tnx

Meron po bang Video Toturial sa paggawa ng Isometric Layout para sa Plumbing??